How to Affix Head to Easysimple Neck Peg

With the neck mostly shaped, I moved on to the next steps – pickup and neck pocket routing.

Routing

This is a set neck guitar and the fretboard is always in the way when it comes time to do the pickup routes, so I at least started them before gluing the neck in.

Since this build has the inlaid pickguard, what I did was screw the pickguard in place and hog out the pickup routes through the pickguard and into the body.

Then after I was done hogging with the drill press, I switched to using a router and template, again routing through to the body.

I was going to keep going and do the full size singlecoil routes after removing the pickguard, but realized that the end of the neck was going to be going through 2 of the 3 pickup routes and would need to be re-routed after the neck was glued in anyway. So, I worked on the neck pocket route next.

This process was pretty similar to the pickup routes, except that I lined up the neck centerline with the centerline of the body and set the end of the neck where I wanted it in order to keep the bridge and pickup placement correct.

Once I knew I had the neck exactly where I wanted it, I taped down pieces of wood on each side of the neck to act as my straight edges for routing.

While I had the router out, I used it on the back of the pickguard. I had previously drilled the holes for the pots and routed a slot for the 5 way switch.

The wooden pickguard is too thick for the switch, so I routed a recessed area into the back of the pickguard. I also recessed the pot holes a bit while I was at it.

The Glue-up

Now that all of that was done, I was able to move on to gluing the neck to the body. This is the point in the build where it really feels like it becomes a guitar.

Inner Pickup Routes

The next thing I did was level off the neck end and finish up the pickup routes. Since the fretboard was now in the way, I had to prop up the templates with a piece of mdf on each side of the pickup area.

It's a little difficult to get the template lined up precisely when it's floating above the surface like that, so I triple checked all of my measurements then proceeded to routing.

Heel Carving

I actually started carving the heel a little bit before gluing the neck. I pretty much just dry-clamped the neck in place and planned out the area where the neck was attaching to the heel of the body. I then moved the body and pre-carved that section of the neck.

I didn't want to do too much to the body part of the heel until after the glue-up so that I would have a flat area to place my clamps.

So, after the glue was dry I did the rest of the heel shaping.

I started with an angle grinder to rough it out, followed by a gouge, razor files, and coarse sandpaper. Here's how it looks all cleaned up.

The Final Touches

To finish up the build, I cut a truss rod cover out of a piece of mother of pearl, drilled holes for the bridge studs and pilot holes for the screws, and did a lot of fine tuning of all the little details.

I did a pre-finish test assembly to see if any more adjustments were needed and it showed me that I needed more room in the pickup and wire routes, so I did that.

Final Sanding

For this guitar, we are aiming for as light of a natural color as possible and a thin open pore feel. To achieve this I am hand applying a crystal clear water based polyurethane. Because of this I sanded to a higher grit than I do with a sprayed finish. I ended up sanding to 400 grit.

Before sanding, I steamed out any dents I found in the wood with a wet shop towel and a soldering iron. This decompresses the wood fibers in the dent and the dents basically disappear.

After the dents were removed, I sanded with 120, 220, 320, and 400. I stopped to wipe down the wood with water in between a couple of the grits to raise the wood grain so that it doesn't end up raising from the water based finish.

I sanded the truss rod cover up to 800 grit.

The hand cramps and lower back pain were worth it.

Time for finish!

Stay tuned.

sulmanruspinfirl71.blogspot.com

Source: https://guitarbasslab.com/attaching-the-neck-to-the-body/

Share this post